This only enables compilation, it doesn't fix any test.
Qt on Android supports process, but not TEST_HELPER_INSTALLS. See also
acdd57cb for winrt.
android-ndk-r10e is used to compile, see
http://doc-snapshots.qt.io/qt5-5.11/androidgs.html .
corelib/io/{qdir,qresourceengine} need to be fixed later.
Done-with: Frederik Gladhorn <frederik.gladhorn@qt.io>
Done-with: Mårten Nordheim <marten.nordheim@qt.io>
Change-Id: I34b924c8ae5d46d6835b8f0a6606450920f4423b
Reviewed-by: Thiago Macieira <thiago.macieira@intel.com>
Reviewed-by: Frederik Gladhorn <frederik.gladhorn@qt.io>
"terminate" and "terminated" both fail on Android since
QThread::terminate not supported on Android. So we should skip them.
Task-number: QTBUG-68596
Change-Id: Id0d1dde2cfa02bb2978e5dd16087bf8f3bf112b0
Reviewed-by: Thiago Macieira <thiago.macieira@intel.com>
This autotest fails on QEMU armv7 builds.
Task-number: QTBUG-68866
Change-Id: Idb4bf39712a22c40f6d779a46ad2dd1f456ef48b
Reviewed-by: Tony Sarajärvi <tony.sarajarvi@qt.io>
This was originally added so that you could replace a T with
QAtomicInteger<T> in the same class and still keep ABI. However, for
legacy reasons, on 32-bit x86, types larger than 4 bytes keep an old
1990s alignment of only 4 bytes, but modern std::atomic<T> for those 8-
byte types enforces an alignment of 8 bytes. Therefore, the requirement
to keep alignment is not possible to guarantee.
In other words: you may not replace T with QAtomicInteger<T> or
std::atomic<T> and assume no ABI breakages in all platforms.
This is a requirement to implement atomicity. An 8-byte type aligned to
only a 4-byte boundary could cross a 16-byte boundary or, worse, cross a
cacheline boundary. Crossing the 16-byte boundary could be bad on some
processors, but crossing the cacheline boundary (addresses ending in
0x3C, 0x7C, 0xCC and 0xFC, or 4 out of 64 possible addresses or 6.25%)
is always bad: the CPUs cannot guarantee an atomic load or store
operation.
See also <https://gcc.gnu.org/bugzilla/show_bug.cgi?id=71660>.
Task-number: QTBUG-67858
Change-Id: If90a92b041d3442fa0a4fffd15283e4615474582
Reviewed-by: Frederik Gladhorn <frederik.gladhorn@qt.io>
These two places were sort of manually implementing QTRY_VERIFY except that they
never time out.
Change-Id: I136e6c7400194327c0475c6acfc019825ccec1b5
Reviewed-by: Friedemann Kleint <Friedemann.Kleint@qt.io>
Reviewed-by: Olivier Goffart (Woboq GmbH) <ogoffart@woboq.com>
Reviewed-by: Sami Nurmenniemi <sami.nurmenniemi@qt.io>
Use QSignalSpy::wait or QTRY_VERIFY instead. This shaved off ~200 ms of the
running time of the test and is more reliable.
Some unconditional qWait()s still remain in this test. They are giving an
opportunity for the wrong thing to happen and thus are not waiting for any
specific condition to be fulfilled.
Task-number: QTBUG-63992
Change-Id: I25a4470fe8d6a5b8b5039b3ed77321d24faa1707
Reviewed-by: Morten Johan Sørvig <morten.sorvig@qt.io>
Reviewed-by: Sami Nurmenniemi <sami.nurmenniemi@qt.io>
Reviewed-by: Edward Welbourne <edward.welbourne@qt.io>
When the thread that got woken up by release() is supposed to release()
to wake up another thread, we were deadlocking. This happened because we
cleared the bit indicating that there was contention when the first
release(). Instead of storing a single bit, we now store the number of
threads waiting.
Task-number: QTBUG-66875
Change-Id: I72f5230ad59948f784eafffd15193873502ecba4
Reviewed-by: Lars Knoll <lars.knoll@qt.io>
all of these iterator classes already have a member operator+, which allows iter+int.
This commits addes non-member operator+, which allows int+iter, and forwards to the member
QList and QArrayData iterators now satisfy RandomAccessIterator concept
Change-Id: I25c1dd8cea299e735d5a5e288dbe23dc1d7a1933
Reviewed-by: Thiago Macieira <thiago.macieira@intel.com>
Also drops a few instances where the dependency was purely runtime,
especially for examples.
Change-Id: I2a0476f79928143596bdb3b8f01193af90574ae8
Reviewed-by: Oswald Buddenhagen <oswald.buddenhagen@qt.io>
This test makes sure that we do not introduce a regression where the
threads exited the inner loop over the queue before the queue was
empty. This was triggered by calling tryTake at least maxThreadCount
times, which left the same number of null pointers in the queue
and caused the inner loop to exit too soon for all the threads.
Change-Id: I3a9d800149b88d09510ddc424667670b60f06a33
Reviewed-by: Lars Knoll <lars.knoll@qt.io>
The issue was introduced by eaee1209f0, so
it affected only 5.9.2.
[ChangeLog][QtCore][QSemaphore] Fixed a regression that would make
tryAcquire() not to wait forever if the timeout was a negative
value. Note: new code is advised to only use -1 to indicate "forever",
as some other functions taking timeout periods do not accept other
values.
Task-number: QTBUG-64413
Change-Id: I57a1bd6e0c194530b732fffd14f58fce60d5dfc9
Reviewed-by: Lars Knoll <lars.knoll@qt.io>
The vast majority is actually switched to QRandomGenerator::bounded(),
which gives a mostly uniform distribution over the [0, bound)
range. There are very few floating point cases left, as many of those
that did use floating point did not need to, after all. (I did leave
some that were too ugly for me to understand)
This commit also found a couple of calls to rand() instead of qrand().
This commit does not include changes to SSL code that continues to use
qrand() (job for someone else):
src/network/ssl/qsslkey_qt.cpp
src/network/ssl/qsslsocket_mac.cpp
tests/auto/network/ssl/qsslsocket/tst_qsslsocket.cpp
Change-Id: Icd0e0d4b27cb4e5eb892fffd14b5285d43f4afbf
Reviewed-by: Lars Knoll <lars.knoll@qt.io>
<future> is needed by QThread::create. Instead of a fragile series
of preprocessor tests, move its detection to a configure test.
This dramatically simplifies the code, but on the other hand ties
the availability of QThread::create() to the system used to compile
Qt (rather the one used to compile an application).
Change-Id: If1b06363379bf29126cfa68f2a0651cbb78a67f7
Reviewed-by: Thiago Macieira <thiago.macieira@intel.com>
When many runnables are executed, this improves the
performance by not resizing the queue for each runnable,
which was the case in the previous version, because of
many calls to QVector::takeFirst().
Also add a test that makes sure tryTake() is safe to
call and does not leave the queue in a bad state that
tries to use nullptr entries.
Change-Id: I608134ecfa9cfc03db4878dcbd6f9c1107e13e90
Reviewed-by: Lars Knoll <lars.knoll@qt.io>
Remaining uses of Q_NULLPTR are in:
src/corelib/global/qcompilerdetection.h
(definition and documentation of Q_NULLPTR)
tests/manual/qcursor/qcursorhighdpi/main.cpp
(a test executable compilable both under Qt4 and Qt5)
Change-Id: If6b074d91486e9b784138f4514f5c6d072acda9a
Reviewed-by: Ville Voutilainen <ville.voutilainen@qt.io>
Reviewed-by: Lars Knoll <lars.knoll@qt.io>
Reviewed-by: Olivier Goffart (Woboq GmbH) <ogoffart@woboq.com>
Remaining uses of Q_DECL_OVERRIDE are in:
src/corelib/global/qcompilerdetection.h
src/corelib/global/qglobal.cpp
doc/global/qt-cpp-defines.qdocconf
(definition and documentation of Q_DECL_OVERRIDE)
tests/manual/qcursor/qcursorhighdpi/main.cpp
(a test executable compilable both under Qt4 and Qt5)
Change-Id: Ib9b05d829add69e98a86238274b6a1fcb19b49ba
Reviewed-by: Lars Knoll <lars.knoll@qt.io>
Reviewed-by: Ville Voutilainen <ville.voutilainen@qt.io>
Reviewed-by: Olivier Goffart (Woboq GmbH) <ogoffart@woboq.com>
Since MSVC doesn't have <chrono> (according to QT_HAS_INCLUDE), the QSKIP
in the test was printed for every line in the table. Instead, add the
skip in the _data() function.
Change-Id: I6e9274c1e7444ad48c81fffd14dbcee5e5a322aa
Reviewed-by: Mårten Nordheim <marten.nordheim@qt.io>
Reviewed-by: Olivier Goffart (Woboq GmbH) <ogoffart@woboq.com>
Allows setting the stack size for the thread pool
worker threads. Implemented using QThread::stackSize.
Task-number: QTBUG-2568
Change-Id: Ic7f3981289290685195bbaee977a23e0c3c49bf0
Reviewed-by: Morten Johan Sørvig <morten.sorvig@qt.io>
Qemu uses some memory for each generated thread. This test creates
> 80000 threads and consumes about 10Gb of memory which is too
heavy for a VM.
Task-number: QTBUG-59966
Change-Id: I1bb8a0d7955778f5201948b41befcb9f1f391514
Reviewed-by: Simon Hausmann <simon.hausmann@qt.io>
tryAcquireWithTimeout(0.2s) was already blacklisted and
now the same failed with "(2s)".
Task-number: QTBUG-58745
Change-Id: I82363238c08056d2969a7616e3a6e5af080d537d
Reviewed-by: Liang Qi <liang.qi@qt.io>
In the spirit of std::thread, which takes a function to call and its
parameters, and runs it in a new thread. Since the user might want to
connect to signals, move QObjects into the new thread, etc., the new
thread is not immediately started.
Although technically all of this _should_ be implementable in pure
C++11, there is nothing in the Standard to help us not reinvent all the
plumbing: packing the decay'd parameters, storing them, invoking the
function over the parameters (honoring INVOKE/std::invoke semantics).
std::function does not do the job, as it's copiable and therefore does
not support move-only functors; std::bind does not have INVOKE
semantics.
I certainly do not want to reimplement all the required facilities
inside of Qt. Therefore, the full blown implementation requires C++17
(std::invoke).
In order to make this useful also in pre-C++17, there are two additional
implementations (C++11 and C++14) that support just a callable, without
any arguments passed to it. The C++11 implementation makes use of a
class to store and call the callable (even move-only ones); basically,
it's what a closure type for a C++14 lambda would look like.
An alternative implementation could've used some of the existing
facilities inside QObject::connect implementation that store a functor
(for the connect() overload connecting to free functions), namely:
the QtPrivate::QFunctorSlotObject class. However:
* QFunctorSlotObject does not support move-only callables (see
QTBUG-60339);
* QFunctorSlotObject itself is not a callable (apparently by design),
and requires to be wrapped in a lambda that calls call() on it;
* the moment QTBUG-60339 is solved, we'd need the same handwritten
closure to keep QFunctorSlotObject working with move-only callabes.
So: just use the handwritten one.
The C++14 implementation is a simplified version of the C++11 one,
actually using a generalized lambda capture (corresponding to the
handwritten C++11 closure type).
All three implementations use std::async (with a deferred launch policy,
a nice use case for it!) under the hood. It's certainly an overkill for
our use case, as we don't need the std::future, but at least std::async
does all the plumbing for us.
[ChangeLog][QtCore][QThread] Added the QThread::create function.
Change-Id: I339d0be6f689df7d56766839baebda0aa2f7e94c
Reviewed-by: Thiago Macieira <thiago.macieira@intel.com>
If the respective modules aren't available we cannot build the tests
and examples. We drop the qtConfig(opengl) requirement for the opengl
examples as
a, we would need to make the QtGui configuration available for that to
work, and
b, we should not add too much detail to the tests and examples build
configurations. Checking each test and example for every feature it
uses would be too much.
Task-number: QTBUG-57255
Change-Id: Ifb043c81ec9e5c487765297bd65704812cd281fc
Reviewed-by: Oswald Buddenhagen <oswald.buddenhagen@qt.io>
It has started failing recently on the CI, too.
Task-number: QTBUG-58745
Change-Id: I4c8834917e6455d00c300549ed448b06da75d5bc
Reviewed-by: Rafael Roquetto <rafael.roquetto@kdab.com>
Let's take the beginning of the description: WaitForSingleObjectEx can
be up to 16 milliseconds early. This is proven by the fact that there
are tests doing:
wait(waitTime);
QVERIFY(timer.elapsed() >= waitTime - systemTimersResolution);
and failing.
Task-number: QTBUG-59337
Change-Id: Iae839f6a131a4f0784bffffd14a9a79523d69d94
Reviewed-by: Olivier Goffart (Woboq GmbH) <ogoffart@woboq.com>
ResultStore never actually exists, only ResutStoreBase does. So casting to
ResultStore<T> and calling its member functions is UB. Put the type dependent
function as template member functions within ResultStoreBase and so we don't
need QtPrivate::ResultStore anymore.
Same goes for the iterator.
Change-Id: I739b9d234ba2238977863df77fde3a4471a9abd2
Reviewed-by: Marc Mutz <marc.mutz@kdab.com>
Replace all QT_NO_PROCESS with QT_CONFIG(process), define it in
qconfig-bootstrapped.h, add QT_REQUIRE_CONFIG(process) to the qprocess
headers, exclude the sources from compilation when switched off, guard
header inclusions in places where compilation without QProcess seems
supported, drop some unused includes, and fix some tests that were
apparently designed to work with QT_NO_PROCESS but failed to.
Change-Id: Ieceea2504dea6fdf43b81c7c6b65c547b01b9714
Reviewed-by: Oswald Buddenhagen <oswald.buddenhagen@qt.io>
The cancel() function added in 5b11e43e for Qt 5.5 suffers from a
number of problems:
First, if runnable->autoDelete() is true, then the function suffers
from the ABA problem (see documentation written for trytake()).
Second, if runnable->autoDelete() is false, due to cancel() throwing
away crucial information instead of returning it, the caller cannot
know whether the runnable was canceled (and thus has to be deleted),
wasn't found or is currently executing (and thus mustn't be deleted),
or has finished executing (and can be used to extract the result).
Deprecate this dangerous API and replace it with the much more useful
Private::stealRunnable(), promoted to public API and renamed to
tryTake() for consistency with the rest of Qt.
Described the various caveats in the function's documentation.
[ChangeLog][QtCore][QThreadPool] The cancel() function suffers from
several subtle issues and has been replaced with a new tryTake()
function.
Change-Id: I93125935614087efa24b3e3969dd6718aeabaa4f
Reviewed-by: Edward Welbourne <edward.welbourne@qt.io>
We keep the runnables from finishing by having them block
on a QSemaphore::acquire() call inside run().
If we fail a test that precedes the call to sem.release()
further into the test, the early return will cause the
thread pool to be destroyed, which will then attempt to
wait for the runnables to finished, which, in turn wait
for the semaphore to be released.
-> dead lock
Fix by introducing a RAII object to release the semaphore
with a sufficiently large number to unblock all runnables.
That number will in some situations be too large, but that
does not matter.
Change-Id: I1ec7e29b37bc36309e93e6e30708cc7db3c9579c
Reviewed-by: Thiago Macieira <thiago.macieira@intel.com>
In order to get reproducible runs of the test, we need to
wait in the main thread until all runnables have started
executing. Otherwise, what the cancel() loop below actually
does will vary from run to run.
Change-Id: Ib912b0943e7bbd55c9480ae6fd4011ba20ac457e
Reviewed-by: Thiago Macieira <thiago.macieira@intel.com>
Instead of allocating a statically-sized array on the heap,
use an automatic C array instead.
Replace some magic numbers with named constants.
Change-Id: I17d29a76a67c4a413453ac26a5dee8cd54a8a37d
Reviewed-by: David Faure <david.faure@kdab.com>
Manipulating a simple int from multiple threads is a data race,
thus undefined behavior.
Fix by using QAtomicInt and atomic operations instead.
Change-Id: I5418bc260da57fe353a71b8e5c7c1c97adbe7597
Reviewed-by: David Faure <david.faure@kdab.com>
When one of the QCOMPAREs in Consumer::run() fails, the consumer
returns early, leaving the producer deadlocked in a QSemaphore's
acquire() call. Change these to tryAcquire() with a large timeout,
so the producer, too, eventually leaves run().
Change-Id: I7421d43305decd4754e09c8e092363594d1be06b
Reviewed-by: David Faure <david.faure@kdab.com>
This test was determined to be flaky on the CI.
Task-number: QTBUG-58741
Change-Id: I43196d3a27f726fb96b427f5071e726b571a0404
Reviewed-by: Friedemann Kleint <Friedemann.Kleint@qt.io>
Reviewed-by: David Faure <david.faure@kdab.com>
This is a simple RAII class that makes semaphore releasing
reliable in the face of exceptions and early returns.
This code originates from KDTools' KDSemaphoreReleaser[1], but
has been extensively reworked to support C++11 move semantics.
[1] https://docs.kdab.com/kdtools/2.3.0/class_k_d_semaphore_releaser.html
[ChangeLog][QtCore][QSemaphore] Added a new RAII class, QSemaphoreReleaser,
to reliably perform release() calls.
Change-Id: I6aff64d37cc0882b17c4419817bde60b542f34d9
Reviewed-by: Mitch Curtis <mitch.curtis@qt.io>
Reviewed-by: David Faure <david.faure@kdab.com>
Reviewed-by: Thiago Macieira <thiago.macieira@intel.com>
This test was determined to be flaky on the CI, depite attempts
to stabilize it (b750a3786f).
Task-number: QTBUG-58745
Change-Id: I933199cd537002699906147d172bb797f1dc90c1
Reviewed-by: Allan Sandfeld Jensen <allan.jensen@qt.io>
The future tests don't need QtConcurrent as QFuture and friends are in
QtCore. The printdevice test doesn't use QtNetwork and the lancelot as
well as the testlib tests don't use QtXml.
Change-Id: I150ac99b36682aa23ad22ba943266eb0f0952838
Reviewed-by: Oswald Buddenhagen <oswald.buddenhagen@qt.io>
This new function does the same as newRow(), except that it has a less confusing
name (in line with _add_Column()), and accepts printf-style arguments to avoid
the need to newRow(qPrintable(QString::asprintf())), a common pattern in client
code. It uses qvsnprintf() under the hoods, avoiding the need for the QString
const char* round-trip.
Port all in-tree users of newRow(qPrintable(QString::asnprintf())) to the new
function.
Change-Id: Icd5de9b7ea4f6759d98080ec30f5aecadb8bec39
Reviewed-by: Thiago Macieira <thiago.macieira@intel.com>
The test was so slow it was blacklisted on all platforms for timing out.
This patch lowers the timeout to a 5th and tries removing the blacklist.
Change-Id: Ib28b21de572517c548a14300f26815598efe91e2
Reviewed-by: Thiago Macieira <thiago.macieira@intel.com>
By templating on the <chrono> types and unconditionally using
duration_cast to coerce the duration into a milliseconds, we
allowed code such as
mutex.try_lock_for(10us)
to compile, which is misleading, since it's actually a zero-
timeout try_lock().
Feedback from the std-discussions mailing list is that the
wait_for functions should wait for _at least_ the duration
given, because that is the natural direction of variance
(tasks becoming ready to run might not get a CPU immediately,
causing delays), while an interface that documents to wait
_no more_ than the given duration is promising something it
cannot fulfill.
Fix by converting the given duration to the smallest number
of milliseconds not less than the original duration. If that
is not representable in an int, use INT_MAX, emulating the
effect of a spurious wakeup, which are allowed to happen if
the function returns false in that case.
In the above example, the try_lock_for call is now equivalent
to
mutex.tryLock(1);
The tryLock() docs state that the actual waiting time does
not exceed the given milliseconds, but fixing that is a
separate issue.
Change-Id: Id4cbbea0ecc6fd2f94bb5aef28a1658be3728e52
Reviewed-by: Thiago Macieira <thiago.macieira@intel.com>
This test fails on Windows occasionally with values just short of 800, the lowest
observed being 791. It is probably rounding somehow to 10ms segments, so allow
it to be up to 10 ms too fast.
Change-Id: Ie28e9f61588b68a9060a006f78eedc3a26d05155
Reviewed-by: Friedemann Kleint <Friedemann.Kleint@qt.io>
Reviewed-by: Thiago Macieira <thiago.macieira@intel.com>
Reviewed-by: Simon Hausmann <simon.hausmann@qt.io>
Consistent with other Unix platforms, and internally consistent between tests,
as a lot of tests were already applying CONFIG -= app_bundle manually.
Change-Id: Icd2b7e1c08015b26137af60ff82fddbc753f0ff4
Reviewed-by: Jake Petroules <jake.petroules@qt.io>
The adoptedThreads test never spawned any thread causing a test error
later on. Hence add a winrt version using __beginthreadex which exists
for that platform.
Change-Id: I04f980218713df20cb41d804d732e0c99b958489
Reviewed-by: Oliver Wolff <oliver.wolff@qt.io>
Now QBasicMutex is Lockable and QMutex is TimedLockable, which means they can
be used in std::lock_guard, std::unique_lock, std::lock, etc.
[ChangeLog][QtCore][QMutex] QMutex now fully models the TimedLockable
concept by providing the try_lock, try_lock_for and try_lock_until
functions, therefore making it usable in Standard Library lock
management classes and functions.
Change-Id: I7c691481a5781a696701e1ab78186b5cefbd6a87
Reviewed-by: Olivier Goffart (Woboq GmbH) <ogoffart@woboq.com>
This requires fixing the test on Windows: QMutex internally uses
WaitForSingleObjectEx which can wake up early, according to the system
timer resolution:
https://msdn.microsoft.com/en-us/library/windows/desktop/ms687069(v=vs.85).aspx#waitfunctionsandtime-outintervals
QTime must be so slow that it hides the early wakes, but QElapsedTimer is
accurate enough to make the test fail unless we add back some tolerance to
compensate for the early wakeups.
Change-Id: I20b38af9c87a0b0e38a19b9bff1c3c24975c78f5
Reviewed-by: Friedemann Kleint <Friedemann.Kleint@qt.io>
Reviewed-by: Thiago Macieira <thiago.macieira@intel.com>
Drop addSub() test. It executes exactly the union of fetchAndAdd()
and fetchAndSub(), which have already had their UBs fixed.
No need to do fixes in duplicated code.
Change-Id: Ib72caab0310fce3ff9a40c261d8a38518f91ecaf
Reviewed-by: David Faure <david.faure@kdab.com>
This change partially reverts 1bfc7f68 about QT_HAS_BUILTIN define
and undef in src/corelib/tools/qsimd_p.h.
This change is also squashed with "Fall back to c++11 standard
compiler flag for host builds" which is done by Peter Seiderer.
Conflicts:
mkspecs/features/default_post.prf
src/3rdparty/sqlite/0001-Fixing-the-SQLite3-build-for-WEC2013-again.patch
src/3rdparty/sqlite/sqlite3.c
src/corelib/tools/qsimd_p.h
src/gui/kernel/qevent.cpp
src/gui/kernel/qwindowsysteminterface.cpp
src/gui/kernel/qwindowsysteminterface_p.h
src/plugins/bearer/blackberry/blackberry.pro
src/plugins/platforms/cocoa/qcocoasystemsettings.mm
src/plugins/platformthemes/gtk2/gtk2.pro
src/plugins/styles/bb10style/bb10style.pro
src/sql/drivers/sqlite2/qsql_sqlite2.cpp
tools/configure/configureapp.cpp
Task-number: QTBUG-51644
Done-with: Peter Seiderer <ps.report@gmx.net>
Change-Id: I6100d6ace31b2e8d41a95f0b5d5ebf8f1fd88b44
Signed integer overflows and underflows are undefined
behavior. A test that invokes UB tests nothing, because
the standard permits any outcome.
Fix by guarding the respective operations so
they are not executed if they would overflow
or underflow.
Change-Id: I40354ee88f40e4b47b70eac7790dc3a79ac70a57
Reviewed-by: Olivier Goffart (Woboq GmbH) <ogoffart@woboq.com>
I wrote a script to help find the files, but I reviewed the
contributions manually to be sure I wasn't claiming copyright for search
& replace, adding Q_DECL_NOTHROW or adding "We mean it" headers.
Change-Id: I7a9e11d7b64a4cc78e24ffff142b506368fc8842
Reviewed-by: Lars Knoll <lars.knoll@theqtcompany.com>
Not that we require it, but since The Qt Company did it for all files
they have copyright, even if they haven't touched the file in years
(especially not in 2016), I'm doing the same.
Change-Id: I7a9e11d7b64a4cc78e24ffff142b4c9d53039846
Reviewed-by: Lars Knoll <lars.knoll@theqtcompany.com>
From Qt 5.7 -> tools & applications are lisenced under GPL v3 with some
exceptions, see
http://blog.qt.io/blog/2016/01/13/new-agreement-with-the-kde-free-qt-foundation/
Updated license headers to use new GPL-EXCEPT header instead of LGPL21 one
(in those files which will be under GPL 3 with exceptions)
Change-Id: I42a473ddc97101492a60b9287d90979d9eb35ae1
Reviewed-by: Thiago Macieira <thiago.macieira@intel.com>
Reviewed-by: Lars Knoll <lars.knoll@theqtcompany.com>
[ChangeLog][Important Behavior Changes] Starting with Qt 5.7, Qt
requires a C++11 compiler with support for C++11 atomics. This affects
user code too: Qt headers no longer compile with a C++98 compiler. The
minimum compiler versions for this release are:
* Clang 3.4 (found in XCode 5.1)
* GCC 4.7
* Microsoft Visual Studio 2012
Change-Id: Ib056b47dde3341ef9a52ffff13ef1f496ea9363f
Reviewed-by: Marc Mutz <marc.mutz@kdab.com>
Reviewed-by: Dmitry Shachnev <mitya57@gmail.com>
TEST_HELPER_INSTALLS cannot be used on platforms with no
QProcess support.
Change-Id: I2a6a283d94ca4487fc628449c53fc37140dd291d
Reviewed-by: Oliver Wolff <oliver.wolff@theqtcompany.com>
Replace hardcoded interval by QTRY_COMPARE() ensuring that all tasks have
finished, since otherwise QThreadPool::tryStart() fails in the next run.
Remove blacklisting for MSVC2012 since it is not compiler-specific.
Task-number: QTBUG-49654
Change-Id: If49b6eb9ef4da4ba2911839166c397d84c175e00
Reviewed-by: Simon Hausmann <simon.hausmann@theqtcompany.com>
Reviewed-by: Jędrzej Nowacki <jedrzej.nowacki@theqtcompany.com>
Introduce constants and make the interval for the 2nd thread a bit
longer.
Task-number: QTBUG-49653
Change-Id: I92ac0494ec6c9af5bde858007d08e26210215434
Reviewed-by: Joerg Bornemann <joerg.bornemann@theqtcompany.com>
Introduce a base class for the threads that ensures termination in the
destructor to ensure all QThreads instantiated on the stack are terminated.
This should reduce crashes since the test thread classes have pointers
to stack variables of the test slots.
Set object names on the threads for better diagnostics.
Decouple wakeOne()/wakeAll() that impact each other via the static count
variables of the thread class by introducing a base class WakeThreadBase
keeping a pointer to an QAtomicInt count variable on the stack instead
(similar to the existing pointers to the mutexes, etc).
Task-number: QTBUG-49653
Change-Id: I73537386bf36019efa81e8e24ba9af92506f7794
Reviewed-by: Frederik Gladhorn <frederik.gladhorn@theqtcompany.com>
If the future is finished when a watcher starts watching it, it is
perfectly reasonable for the watcher to get the finished message
promptly. If you pause the watcher before any message loops get to
run, the message presently won't get through until the watcher is
resumed, but there is no reason to guarantee that; indeed, one could
consider it somewhat perverse behavior.
So move the reportFinished() calls to after the pause()s.
Also eliminate a used-once local variable and use QTRY_VERIFY() in one
place where qWait() was used before.
Change-Id: I4bc6091fd7437a4d341be511b7a140f3d72d850e
Reviewed-by: Marc Mutz <marc.mutz@kdab.com>
Attaching spies afterwards was provoking a warning during tests:
QFutureWatcher::connect: connecting after calling setFuture() is likely to produce race
Change-Id: I6ee8c3613cecebd1c69b0337139d8a19a33f4a11
Reviewed-by: Marc Mutz <marc.mutz@kdab.com>
Liang Qi
Mårten Nordheim
Joni Jantti
Tony Sarajärvi
Thiago Macieira
Qt Forward Merge Bot
Kari Oikarinen
Eric Lemanissier
Friedemann Kleint
Allan Sandfeld Jensen
Svenn-Arne Dragly
Giuseppe D'Angelo
Kevin Funk
Morten Johan Sørvig
Sami Nurmenniemi
Ulf Hermann
Marc Mutz
Olivier Goffart
Allan Sandfeld Jensen
Tor Arne Vestbø
Maurice Kalinowski
Liang Qi
Friedemann Kleint
Simon Hausmann
Jani Heikkinen
Maurice Kalinowski
Edward Welbourne